750-200-DC

• Deutz model BF6M1013 turbocharged and aftercooled, six-cylinder, liquid-cooled, diesel engine providing 170 horsepower, 127 kW.
• Waterous CXVT centrifugal fire pump. CXVT utilizes a high−tensile gray iron body, bronze impeller, replaceable wear rings and maintenance−free mechanical seals.
• Intake: 6 inch

1000-200-DC

• Deutz model BF6M1013 turbocharged and aftercooled, six-cylinder, liquid-cooled, diesel engine providing 192 horsepower, 143 kW.
• Waterous CXVT centrifugal fire pump. CXVT utilizes a high−tensile gray iron body, bronze impeller, replaceable wear rings and maintenance−free mechanical seals.
• Intake: 6 inch

1250-200-DC

• Deutz model BF6M1013C turbocharged and aftercooled, six-cylinder, liquid-cooled, diesel engine providing 231 horsepower, 172 kW.
• Waterous CXVT centrifugal fire pump. CXVT utilizes a high−tensile gray iron body, bronze impeller, replaceable wear rings and maintenance−free mechanical seals.
• Intake: 6 inch

ALL MODELS

• Air Compressor
• Oil−flooded, rotary screw type air compressor, sized to supply a minimum of 200 sCFM (5.6 m3/min) of usable air.
• Pneumatic Modulating Inlet Valve controls air delivery while maintaining constant pressure.
• Auto Sync™ Balancing System automatically maintains the air pressure within +/− 5% of the water pump pressure throughout the pressure range.
• Air Compressor Oil System contains a spin−on, full−flow oil filter unit and a thermostatic valve to control oil flow to the cooler.
• Air / Oil separator head assembly with spin-on cartridge.
  Air Compressor Cooling System uses the unit’s water pump, a copper and brass shell and tube heat exchanger to cool the compressor. The system maintains recommended operating temperatures throughout the full operational range in ambient temperatures up to 115°F (46.1°C). A “fail safe” switch precludes engagement of the compressor PTO unless the fire pump is engaged.
• Air compressor transmission contains a “Poly-Chain” drive and 8mm pitch sprockets.
  
  Panel Mounted Instruments
• The following items and controls are provided for installation on the pump operator’s panel:
  - Pump engine tachometer
  - Pump engine hourmeter
  - Pump engine oil pressure gauge w/light and alarm
  - Pump engine coolant temp. gauge w/light and alarm
  - Compressor temp. gauge w/warning light and alarm
  - Pump engine voltmeter
  - Engine ignition/start switch
  - AutoSync pressure balance controls and instruction plate
  
  Engine Specifications
• Heavy-duty muffler
• Pressure lubrication system with oil pressure warning light and spin−on oil filter. An extension hose is installed on the engine oil drain with a valve located at the oil pan and a plug installed in the end of the hose to facilitate oil changes.
• 12−volt electric with 55A alternator, electric ignition and start switch.
• 5-year warranty
  

• Pressure Relief: An optional pressure relief system is available to comply with NFPA 1906 standards.
• Priming System: Pneumatic oil−free primer capable of priming the water pump through 20 feet (6 m) of 2−1/2 (63.5 mm) inch hard intake hose with a 10 foot (3 m) lift. Controls are mounted on the operator’s panel.
• Foam Systems: Aquis™ Foam Proportioner or Advantus® Foam System
• On-site operation and maintenance instruction. Contact factory for pricing.

Spec Sheets:
500-200-DC, 750-200-DC, 1000-2...

Operational Guide:
1250-200-DC

Industry-leading sales and support.
When you purchase Waterous equipment, not only do you get quality products, you get quality service. Our expert service technicians are the best in the business and they are always happy to answer any service questions you might have. The numbers for our service and training specialists are listed below for your convenience. If you have a general service question please call our main number and our staff will kindly direct you to the appropriate department.

Sales/Applications Assistance
Phone: 651-450-5234 (Press 3)
sales&service@waterousco.com

Service Assistance
Phone: 651-450-5200
Fax: 800-488-1228
sales&service@waterousco.com