Eclipse

Slide-In

Integrated Cross-Mount

Air Compressor Modules

PTO

PTO Kits

	Specs

	Options/ Accessories

	Download Literature

	Sales/Application/ Service Help

A Medium Sized Slide-In Compressed Air Foam Fire Suppression Water Pump with Big Performance

Our slide-in, portable modular compressed air foam 100-50-DS unit is designed and constructed to simultaneously discharge water, foam solution or compressed air foam, developing 80 GPM of water at 125 PSIg (300 L/min. @ 8.6 bar) and 40 CFM of air at 125 PSIg (1.13 m3/min @ 8.6 bar). The 100-50-DS also features compressed air for pneumatic tools and can pump water or air independently.

Low Maintenance
Your 100-50-DS compressed air foam system’s service and maintenance needs are covered Waterous’ exclusive 5-year warranty. When compared with apparatus equipped with other brands of compressed air foam systems, our service technicians will have the power behind the slide-in 100-50-DS CAFSystem™ repaired and back in service in no time.

Product Orientation & Integration
Implementing a 100-50-DS CAFSystem™ into your department may seem intimidating, but Waterous factory personnel can provide on-site product operation and maintenance instruction to eliminate the learning curve of integrating CAFS. If the utilization of compressed air foam is a new technology to your brand of fighting fires, contact your Waterous representative for exclusive pricing on courses today.

Options & Accessories
The 100-50-DS CAFSystems™ come with a variety of options to fit the needs of your fire department and easily interface with numerous accessories and foam solutions. Combined with a Waterous AquisTM foam proportioner makes the 100-50-DS a crucial tool for maximizing your fire suppression capabilities. A 250 or 350 gallon (946 to 1325 liters) water tank is also available.

Model 100-50-DS

Specifications

Air Compressor

Oil−flooded, rotary screw type air compressor, sized to supply a minimum of 50 sCFM (1.42 m3/min) of usable air.
Pneumatic Modulating Inlet Valve controls air delivery while maintaining constant pressure.
Auto Sync™ Balancing System automatically maintains the air pressure within +/− 5% of the water pump pressure throughout the pressure range.
Air Compressor Oil System contains a spin−on, full−flow oil filter unit and a thermostatic valve to control oil flow to the cooler.
Air / Oil separator head assembly with spin-on cartridge.
Air Compressor Cooling System uses the unit’s water pump, a copper and brass shell and tube heat exchanger to cool the compressor. The system maintains recommended operating temperatures throughout the full operational range in ambient temperatures up to 115°F (46.1°C).
Air compressor transmission contains a “Poly-Chain” drive and 8mm pitch sprockets.

Engine Specifications
Briggs & Stratton Vanguard 3/LC, Model DM 950 D, three-cylinder, liquid−cooled, developing 31 horsepower at 3600 rpm (23.6 kW), four−cycle, diesel fueled.
Heavy-duty muffler
Pressure lubrication system with oil pressure warning light and spin−on oil filter. An extension hose is installed on the engine oil drain with a valve located at the oil pan and a plug installed in the end of the hose to facilitate oil changes.
12−volt electric with 40A alternator, electric ignition and start switch.

Pump Specifications
Hypro® centrifugal water pump utilizing close−grained iron case, reinforced-nylon impeller, stainless steel shaft and maintenance−free mechanical seal.
Intake: 1-1/2 inch
Discharge: 1-1/2 inch

Priming System
Jet Prime System: Pneumatic oil−free primer capable of priming the water pump through 20 feet (6 m) of 2−1/2 (63.5 mm) inch hard intake hose with a 10 foot (3 m) lift. Controls are mounted on the operator’s panel.

Plumbing
Inlet: Inlet piping is 2” stainless steel pipe with a 2” tank to pump valve controlled at the pump panel. A 2” valve is provided behind the pump panel for overboard pump inlet with a 1.5” M−NST connection.
Discharge: Plumbing to two panel mounted 1.5” discharge outlets incorporate a stainless steel manifold, welded stainless steel pipe and/or Class 1 high−pressure hydraulic hose with stainless steel fittings. A 1” tank fill provision with 1” valve is provided.

Water / Foam Tanks
200 gallon (757 liter) water tank
10 gallon (38 liter) foam poly tank

Foam Proportioner
A FoamPro® System 1601 automatic foam proportioner (Class A foam only) is provided and installed to inject foam concentrate into all discharges. The proportioner automatically meters the correct percentage of foam concentrate into the water stream by a 1.5” paddlewheel sensor

Pump Operator’s Panel incorporated into frame
Contains Auto Sync, air compressor, foam proportioner controls, and water pressure and air pressure gauges.

< Back to top

Options and Accessories

Foam Proportioner: Aquis™ Foam Proportioner
250 or 350 gallon (946 to 1325 liters) water tank available.
On-site operation and maintenance instructions
Contact factory for pricing.

< Back to top

Download Product Literature


Spec Sheets: 100-50-DS Aquis™ 1.5 Foam Proportioner Aquis™ 2.5 Foam Proportioner Operational Guide: 100-50-DS		Product Brochures: CAFSystems™
< Back to top

Sales/Application/Service Help

Industry-leading sales and support.
When you purchase Waterous equipment, not only do you get quality products, you get quality service. Our expert service technicians are the best in the business and they are always happy to answer any service questions you might have. The numbers for our service and training specialists are listed below for your convenience. If you have a general service question please call our main number and our staff will kindly direct you to the appropriate department.

Sales/Applications Assistance
Phone: 651-450-5234 (Press 3)
pumpsales@waterousco.com

Service Assistance
Phone: 651-450-5200
Fax: 800-488-1228
service@waterousco.com

< Back to top