 |
|
|
|
|
|
CAFSystems™: 200-100-DS
Heavy Duty Slide-In’s for Heavy Duty Applications. |
|
The 200-100-DS delivers water, aspirated foam, or compressed air foam simultaneously, as well as compressed air for pneumatic tools. The 200-100-DS discharges water, foam solution or compressed air foam, developing 200 GPM of water at 125 PSIg (757 L/min @ 8.6 bar) and 100 CFM of air at 125 PSIg (2.83 m3/min @ 8.6 bar) simultaneously. The 200-100-DS also comes with an industry exclusive five-year warranty. |
Model 200-100-DS
|
|
| |
|
| |
|
- Air Compressor
- Oil−flooded, rotary screw type air compressor, sized to supply a minimum of 100 sCFM (2.83 m3/min) of usable air.
- Pneumatic Modulating Inlet Valve controls air delivery while maintaining constant pressure.
- Auto Sync™ Balancing System automatically maintains the air pressure within +/− 5% of the water pump pressure throughout the pressure range.
- Air Compressor Oil System contains a spin−on, full−flow oil filter unit and a thermostatic valve to control oil flow to the cooler.
- Air / Oil separator head assembly with spin-on cartridge.
- Air Compressor Cooling System uses the unit’s water pump and a copper and brass shell and tube heat exchanger to cool the compressor. The system maintains recommended operating temperatures throughout the full operational range in ambient temperatures up to 115°F (46.1°C).
- Air compressor transmission contains a “Poly-Chain” drive and 8mm pitch sprockets.
Engine Specifications
- Deutz, three-cylinder, turbocharged, liquid-cooled, delivering a maximum of 60 horsepower (44.7 kW), four-cycle, diesel fueled.
- Heavy-duty muffler
- Pressure lubrication system with oil pressure warning light and spin−on oil filter. An extension hose is installed on the engine oil drain with a valve located at the oil pan and a plug installed in the end of the hose to facilitate oil changes.
- 12−volt electric with 60A alternator, electric ignition and start switch.
Pump Specifications
- Waterous CPD−2 centrifugal fire pump. CPD−2 utilizes an aluminum body, bronze impeller, replaceable wear rings and maintenance−free mechanical seals.
- Intake: 3 inch
- Discharge: 2 inch
Priming System
- Prime System: Pneumatic oil−free primer capable of priming the water pump through 20 feet
(6 m) of 2−1/2 (63.5 mm) inch hard intake hose with a 10 foot (3 m) lift. Controls are mounted on the operator’s panel.
Plumbing
- Inlet: Inlet piping is 3” stainless steel pipe.
- Discharge: Plumbing to two panel mounted 1−1/2” discharge outlets incorporate a stainless steel manifold and welded stainless steel pipe.
Foam Proportioner
- An Aquis 1.5 automatic foam proportioner (Class A foam only) is provided and installed to inject foam concentrate into all discharges. The proportioner automatically meters the correct percentage of foam concentrate into the water stream by a 1.5” paddlewheel sensor.
Pump Operator’s Panel incorporated into frame
- Contains Auto Sync, air compressor, foam proportioner controls, and water pressure and air pressure gauges.
|
< Back to top |
| |
|
|
| |
|
| |
|
- Onsite operation and maintenance instruction. Contact factory for pricing.
- Electric Automatic Discharge Valves with electric air valves
|
< Back to top |
| |
|
|
| |
|
| |
|
|
| |
|
| |
|
Industry-leading sales and support.
When you purchase Waterous equipment, not only do you get quality products, you get quality service. Our expert service technicians are the best in the business and they are always happy to answer any service questions you might have. The numbers for our service and training specialists are listed below for your convenience. If you have a general service question please call our main number and our staff will kindly direct you to the appropriate department.
Sales/Applications Assistance
Phone: 651-450-5234 (Press 3)
sales&service@waterousco.com
Service Assistance
Phone: 651-450-5200
Fax: 800-488-1228
sales&service@waterousco.com |
< Back to top |
| |
|
|
|
|
