90-45-GS SLide-In/Portable CAFSystem™
Our slide-in, portable 90-45-GS modular compressed air foam system is designed and constructed to simultaneously discharge water, foam solution or compressed air foam at 60 GPM of water at 125 PSIg (227 L/min. @ 8.6 bar) and 30 CFM of air at 125 PSIg (0.9 m3/min @ 8.6 bar). The 90-45-GS also features compressed air for pneumatic tools and can pump water or air independently.
Low Maintenance
Backed by an exclusive 5-year warranty, we’ve got you taken care of when it comes to service and maintenance needs for your 90-45-GS CAFS compressed air foam system. The pump power behind the 90-45-GS CAFSystem™ can be repaired and back in service faster than apparatus equipped with other brands of compressed air foam systems.
Product Orientation & Integration
If the utilization of compressed air foam is a new technology to your brand of firefighting, implementing a 90-45-GS CAFSystems™ into your department may seem a daunting task. Eliminate the learning curve of integrating CAFS into your daily operations, Waterous factory personnel provide on-site product operation and maintenance instruction. For exclusive pricing on courses, contact your Waterous representative today
Options & Accessories
The 90-45-GS CAFSystems™ come with a variety of options to fit the needs of your fire department and easily interface with numerous accessories and foam solutions. Combined with a Waterous AquisTM foam proportioner makes the 80-40-E a crucial tool for maximizing your fire suppression capabilities. A 250 or 350 gallon (946 to 1325 liters) water tank is also available.
Specifications
Air Compressor
- Oil−flooded, rotary screw type air compressor, sized to supply a minimum of 30 sCFM (0.9 m3/min) of usable air.
- Pneumatic Modulating Inlet Valve controls air delivery while maintaining constant pressure.
- Auto Sync Balancing System automatically maintains the air pressure within +/− 5% of the water pump pressure throughout the pressure range.
- Air Compressor Oil System contains a spin−on, full−flow oil filter unit and a thermostatic valve to control oil flow to the cooler.
- Air / Oil separator head assembly with spin-on cartridge.
- Air Compressor Cooling System uses the unit’s water pump, a copper and brass shell and tube heat exchanger to cool the compressor. The system maintains recommended operating temperatures throughout the full operational range in ambient temperatures up to 115°F (46.1°C).
- Air compressor transmission contains a “Poly-Chain” drive and 8mm pitch sprockets
Engine Specifications
- Briggs, two−cylinder, liquid−cooled, delivering a maximum of 27 horsepower (20.1 kW), four−cycle, gasoline fueled.
- Spark-arresting muffler
- Pressure lubrication system with oil pressure warning light and spin−on oil filter. An extension hose is installed on the engine oil drain with a valve located at the oil pan and a plug installed in the end of the hose to facilitate oil changes
- 12−volt electric with 35A alternator, electric ignition and start switch.
Pump Specifications
- Hypro® centrifugal water pump utilizing close−grained iron case, reinforced-nylon impeller, stainless steel shaft and maintenance−free mechanical seal.
- Intake: 1-1/2 inch
- Discharge: 1-1/2 inch
Priming System
- Prime System: Pneumatic oil−free primer capable of priming the water pump through 20 feet (6 m) of 2−1/2 (63.5 mm) inch hard intake hose with a 10 foot (3 m) lift. Controls are mounted on the operator’s panel.
Plumbing
- Inlet: Inlet piping is 2” stainless steel pipe with a 2” tank to pump valve controlled at the pump panel. A 2” valve is provided behind the pump panel for overboard pump inlet with a 1.5” M−NST connection.
- Discharge: Plumbing to two panel mounted 1.5” discharge outlets incorporate a stainless steel manifold, welded stainless steel pipe and/or Class 1 high−pressure hydraulic hose with stainless steel fittings. A 1” tank fill provision with 1” valve is provided.
Water / Foam Tanks
- 200 gallon (757 liter) water tank
- 10 gallon (38 liter) foam poly tank
Foam Proportioner
- A FoamPro® System 1601 automatic foam proportioner (Class A foam only) is provided and installed to inject foam concentrate into all discharges. The proportioner automatically meters the correct percentage of foam concentrate into the water stream by a 1.5” paddlewheel sensor
Pump Operator’s Panel incorporated into frame
- Contains Auto Sync, air compressor, foam proportioner controls, and water pressure and air pressure gauges.
< Back to Top
Options and Accessories
- Foam Proportioner: Aquis™ Foam Proportioner
- 250 or 350 gallon (946 to 1325 liters) water tank available.
- On-site operation and maintenance instructions
- Contact factory for pricing.
< Back to Top
Download Product Literature
Product Brochures:
Operational Guide:
< Back to Top
Sales/Application/Service Help
Industry-leading sales and support.
When you purchase Waterous equipment, not only do you get quality products, you get quality service. Our expert service technicians are the best in the business and they are always happy to answer any service questions you might have. The numbers for our service and training specialists are listed below for your convenience. If you have a general service question please call our main number and our staff will kindly direct you to the appropriate department.
Sales/Applications Assistance
Phone: 651-450-5234 (Press 3)
pumpsales@waterousco.com
Service Assistance
Phone: 651-450-5200
Fax: 800-488-1228
service@waterousco.com
< Back to Top
